Please select a shopping list
SKU
HJ-6A

Extended pivot joint set

Extend pivot joint set steel bk
USD$3.29

In stock

  • Compatible with 28 mm pipes
  • Assembly required
  • Parts sold separately

The HJ-6A is a black metal joint set that allows you to create a two-pipe intersection with an adjustable angle up to 260 degrees. This joint set allows working with a wider angle radius than the HJ-6 allows. It can be used for many applications such as the creation of angular sides and top or V-shaped racks with angles wider than 90 degrees. The distance created between the two pipes is used for supporting pannels or manufacturing parts.

To assemble an HJ-6A you need to combine two H-6A and two H-6 together with two M6-25B bolts and two M6-N nuts.

Installation Steps:
See the installation steps tab to view how to assemble this connector.

Antistatic Version (ESD):
An electric conductivity version if offered if you wish to build antistatic structures: HJ-6ANP

Want to reuse parts of your old system?
The HJ-6A Flexpipe joint set is compatible with many other pipe and connector systems. Check the technical information tab to know which systems are compatible and none-compatible with our parts.

More Information
Best SellerNo
Units per boxNA
Needed parts2 (H6A) + 2 (H6) + 3 (M6-25B) + 3 (M6-N)
Length inches3 1/2 in (89 mm)
Width inches1 5/16 in (33 mm)
External height inches5 7/16 in (138mm)
External width inches1 5/16 in (33mm)
External depth inches1 5/16 in (33mm)
Steel thickness inches1/8 in (2.5 mm)
Unit weight pounds0.609 lbs (0.277 kg)
Compatible joint systemsCreform, NIS, C Tek Lean Solutions, Trilogiq (28 mm)
None compatible joint systemsFastube, Trilogiq (28.6 mm)
RoHS certificationYes
RecyclableYes
Compatible pipe systemsCreform, Fastube, Trilogiq (28 mm), NIS (28 mm), C Tek Lean Solutions (28 mm)
None compatible pipe systemsTrilogiq (28.6 mm)
Frequency of useVery low
ReusableYes
Reusable partsYes
range of motion260°
Electric conductivity (ESD)No
MaterialHot rolled steel (SPHC)
Steel hardness (HRB)68-75 HRB
FinishGlossy
UV resistanceHigh
System operational temperature-148°F to 572°F (-100°C to 300°C)
Steel treatmentBlack cathodic electrodeposition (Ecoating)
Manufacturing techniqueStamping and deburring
Striations for grip8 striation grip lines
Positioning guide8 positioning guide lines
Additional reinforcement holeNone
1- Make sure you have the following parts:
2 H-6
2 H-6A
2 M6-25B
2 M6-N
2 28mm pipes of your choice
1 Allen key or drill equipped with an Allen Key 5mm tip
2- Take a connector H-6 and install it in the desired location on the P1 pipe.
3-Take a M6-25B bolt and a M6-N nut and insert them into the corresponding openings , making sure to put the bolt on the most accessable side..
4 - Tighten completely the M6-25B bolt and M6-N nut together until the H-6 connectors attached firmly to the P1 pipe . A force of 9.8 Nm is recommended for this step.
5- Repeat step two with H-6A connectors and P2 pipe.
6-Reapeat step three with H-6A connectors.
7- Reapeat step four with H-6A connectors.
8- Align remaining holes of H-6 and H -6A connectors and adjust the angle of the pipes.
9-Take a M6-25B bolt and a M6-N nut and insert them into the remaining openings. Make sure to put the bolt on the more accessible side.
10- Tighten completely the M6-25B bolts and M6-N nuts together until the HJ-6A attached firmly to the P1 and P2 pipes . A force of 9.8 Nm is recommended for this step.