The HJ-12NP is a chrome-plated joint set with antistatic properties (ESD) that rotates 360 degrees. Very similar to the HJ-1NP, the HJ-12NP allows a rotation once this connector is fixed.
This joint set is frequently used to create doors, movable separators and foldable shelves. Psst! If you don't need this joint set to be mobile, the HJ-1NP may be a better fit for your needs.
This joint set is designed with 4 striations for a better grip on the plastic coating of the 28 mm pipes. It also includes 2 additional pre-drilled reinforcement holes to ensure extra strength to your structure. By adding a self-drilling screw F-A85/8, you will solidify the connector joints positioned on a corner where there is a higher risk of impact.
See the installation steps tab to view how to assemble this connector.
Non-Electric Conductivity Version:
A version of this joint set is offered without antistatic properties: HJ-12
Want to reuse parts of your old system?
The HJ-12NP Flexpipe joint set is compatible with many other pipe and connector systems. Check the technical information tab to know which systems are compatible and none-compatible with our parts.
|Units per box||NA|
|Needed parts||2x H-12NP + 1x AP-HINGE + 1x M6-25BWZ + 1x M6-NWZ|
|Length inches||3 5/16 po (84 mm)|
|Width inches||1 5/16 in (33 mm)|
|External height inches||1 7/16 in (36mm)|
|External width inches||3 5/16 in (84mm)|
|External depth inches||1 1/2 in (38mm)|
|Steel thickness inches||1/8 in (2.5 mm)|
|Unit weight pounds||0.310 lbs (0.141 kg)|
|common uses||pivot, perpendicular tubes hinge|
|Compatible joint systems||Creform, NIS, C Tek Lean Solutions, Trilogiq (28 mm)|
|None compatible joint systems||Fastube, Trilogiq (28.6 mm)|
|Compatible pipe systems||Creform, Fastube, Trilogiq (28 mm), NIS (28 mm), C Tek Lean Solutions (28 mm)|
|None compatible pipe systems||Trilogiq (28.6 mm)|
|Frequency of use||Low|
|range of motion||360°|
|Electric conductivity (ESD)||Yes|
|Material||Hot rolled steel (SPHC)|
|Steel hardness (HRB)||68-75 HRB|
|Corrosion resistance||240 hours salt spray corrosion test|
|System operational temperature||-148°F to 572°F (-100°C to 300°C)|
|Steel treatment||Chrome plating|
|Manufacturing technique||Stamping and deburring|
|Striations for grip||4 striation grip lines|
|Positioning guide||4 positioning guide lines|
|Additional reinforcement hole||2 reinforcement holes|
- Ensure you have the following parts:
- 2x H-12NP
- 1x AP-HINGE bracket
- 1x M6-25BWZ bolt
- 1x M6-NWZ nut
- 2x 28mm ESD pipes of your choice
- 1x T-HANDLE 5mm hex key
- Take the AP-HINGE bracket and press it on the first pipe until it clips on, place the opening of the AP-HINGE toward inside of your structure.
- Group the two H-12NP connectors around the first pipe so that the teeth of the AP-HINGE fit into the corresponding openings of the connectors, ensuring proper installation.
- Fix the connectors together by placing the M6-25BWZ bolt with the M6-NWZ nut in the corresponding openings and completely tighten until the HJ-12NP joint set is firmly attached to the pipe. Make sure to place the bolts on the most accessible side. A force between 12-14 Nm is recommended for this step.
- If the HJ-12NP joint set feels too tight to rotate, apply a lubricant spray to ease the mobility of the AP-HINGE and to avoid damaging the plastic teeth.
- Add a metal screw to the pre-drilled reinforcement hole to secure the connector on the second pipe. This can be useful when this connector is used to make shelvings and prevent the material from falling.
Use without the AP-HINGE when space is limited and you need to overlap two joints.
Need more informations ?
Here's everything you need to know!