Please select a shopping list
SKU
HJ-14

Double pivot joint set

Double pivot joint set steel bk
CDN$4.40

In stock

  • Compatible with 28 mm pipes
  • Assembly required

The HJ-14 is a black metal joint set allows creating an intersection of three pipes with an adjustable angle on each side of the cross tube.

To assemble an HJ-14 you need to put two H-14 with four H-6, four M6-25B bolts and four M6-N nuts. It is also possible to assemble the HJ-14 with four H-6A's.

Assembly tip:
This joint set is very similar to a doubled HJ-6. It is frequently used for reinforcing structures, or to create articulations and anchors. This joint set allows each side tube to rotate up to 175 degrees.

Technical Information:
This joint set is designed with 8 striations for a better grip on the plastic coating of the 28 mm pipes. These grips are found on the H-6 or H-6A.

Installation Steps:
See the installation steps tab to view how to assemble this connector.

Antistatic Version (ESD):
An electric conductivity version if offered if you wish to build antistatic structures: HJ-14NP

Want to reuse parts of your old system?
The HJ-14 Flexpipe joint set is compatible with many other pipe and connector systems. Check the technical information tab to know which systems are compatible and none-compatible with our parts.

More Information
Best SellerNo
Units per boxNA
Needed parts4x H-6 + 2x H-14 + 4x M6-25B + 4x M6-N
Length inches3 13/16 in (97 mm)
Width inches1 5/16 in (33 mm)
External height inches1 5/16 in (33mm)
External width inches1 13/16 in (46mm)
External depth inches1 5/16 in (33mm)
Steel thickness inches1/8 in (2.5 mm)
Unit weight pounds0.845 lbs (0.384 kg)
Compatible joint systemsCreform, NIS, C Tek Lean Solutions, Trilogiq (28 mm)
None compatible joint systemsFastube, Trilogiq (28.6 mm)
RoHS certificationYes
RecyclableYes
Compatible pipe systemsCreform, Fastube, Trilogiq (28 mm), NIS (28 mm), C Tek Lean Solutions (28 mm)
None compatible pipe systemsTrilogiq (28.6 mm)
Frequency of useVery low
ReusableYes
Reusable partsYes
range of motion2 X 180°
Electric conductivity (ESD)No
MaterialHot rolled steel (SPHC)
Steel hardness (HRB)68-75 HRB
FinishGlossy
UV resistanceHigh
System operational temperature-148°F to 572°F (-100°C to 300°C)
Steel treatmentBlack cathodic electrodeposition (Ecoating)
Manufacturing techniqueStamping and deburring
Striations for grip8 striation grip lines
Positioning guide8 positioning guide lines
Additional reinforcement holeNone
  1. Ensure you have the following parts:
    • 4x H-6
    • 2x H-14
    • 4x M6-25B bolts
    • 4x M6-N nuts
    • 3x 28mm pipes of your choice
    • 1x T-HANDLE 5mm hex key
  2. Take two H-6 connectors and group them around the first pipe. Fix the connectors by placing an M6-25B bolt and an M6-N nut in the corresponding openings until it's firmly attached to the pipe. Make sure to place the bolts on the most accessible side. A force between 12-14 Nm is recommended for this step.
  3. Repeat step 1 with the second pipe.
  4. Group the two H-14 connectors around the third pipe, and insert the H-6 connectors attached on the first pipe in between the H-14 connectors through corresponding openings. Fix the connectors by placing the M6-25B bolt with the M6-N nut in the corresponding openings and loosely tighten. Make sure to place the bolts on the most accessible side.
  5. Repeat step 3 with the second pipe on the opposite side of the H-14.
  6. Position the first and second pipes into desired angles and tighten completely until the H-14s are firmly attached to the H-6 connectors. Make sure to place the bolts on the most accessible side. A force between 12-14 Nm is recommended for this step.